WE PRESENT YOU THE NEW MANAGEMENTABLE SWITCH IN LAYER 2 QNAP QSW-M2106PR-22S2Tthe new beast of Qnap comes not only with port 10 gbe, but also Poe ++ Capacity up to 310Wweighing for high speed and surveillance Wi-Fi implantations.
For this it has its complete QSS operating systemadding a total of 6 ports 2.5 Gbe Poe ++, another 2 ports 10 Gbe Poe ++ and 2 SFP+10 Gbe To extend the network with more high -speed devices. Let's see what it offers!
We appreciate QNAP His trust in us when sending this switch for analysis.
QNAP QSW-M2106PR-22S2T Technical characteristics
Unboxing
QNAP QSW-M2106PR-22S2T Use a usual presentation in the brand with rigid cardboard box with neutral finish, where we have a sticker with device information.
Inside, we have the switch wrapped in an insulating plastic bag holding two cardboard molds.
The content of the package will be as follows:
- QNAP QSW-M2106PR-22S2T
- Power cable with European plug
- Rack assembly adapter
- Desktop Leg Kit
- Fixing screws
- Documentation
External analysis
QNAP QSW-M2106PR-22S2T It is made of a fairly thick steel frame, and designed for installation in Medium width rackswith a 43.3 mm thickness.
Said frame consists of a upper lid which gives access to the hardware, with a single upper screw, the front panel and another lower cover that also integrates the sides.
In the lateral areas we have the corresponding threaded holes for fixing rack cabinetsbut we are also given the possibility of placing 4 covers that will act as desktop legs.
He Rear panel has the taking of type C14 feeding, Already both sides we find two axial fans to refrigerate the interior.
Port panel
The area of greatest interest of this QNAP QSW-M2106PR-22S2T It will be your front panel, where all the device network connectivity is concentrated:
- LED panel (information, energy and ventilation)
- 1x RJ45 of administration
- 6x RJ45 2.5 Gbe Poe ++
- 2x RJ45 10 Gbe Poe ++
- 2x SFP+ 10GBE
- Reset button
The greatest advantage or characteristic of this switch compared to other brand options is that, in addition to high -speed ports, we also have POE with the IEEE 802.3AF/AT/BT standards.
This means that Each port is capable of delivering until 90W of maximum powerboth in the 2.4 GBE ports and in those of 10 GBE.
The limit will mark your Maximum 310W powerthat is, these 310W will be distributed in the Poe used ports, in case the connected devices exceed this capacity.
As for the switching capacitythis switch supports a total of 110 Gbpswith total yield without 55 Gbps block. Has a table of 16K MAC addressing and support for Jumbo frames of 9k.
All ports They support link aggragationallowing to generate 5 GBE or up to 20 GBE links.
He Indicator LED Right of each port corresponds to the Poe capacity, while the left indicates the use of network data.
Interior of the QNAP QSW-M2106PR-22S2T
We remove the rear screw placed on the upper face, thus extracting metal lid to access the interior of the QNAP QSW-M2106PR-22S2T.
Closer to the fans we find the power supply, of a fairly wide size given its maximum capacity, distributing the energy to the motherboard by means of two EPS of 4 pins. Next to it we have a Planar model transformer Pa6605-Ala de Coilcraft.
The main chips use passive aluminum dissipators with a total of 4 units, while fans have 4 -pin headers for their PWM control.
Switch firmware and characteristics
QNAP QSW-M2106PR-22S2T It is a managing switch in layer 2, which means we will have the QNAP QSS Operating System Inside.
Firmware access can be done:
- By Qfinder Prosoftware that probes the network looking for QNAP devices, which also allows monitoring its status, providing access credentials and updating the firmware among other things.
- Through the IP address assigning the router or server to which it is connected. In case of not being connected, the default IP will be 254,100,101.
Finally, the First access credentials They will be user: admin, password: Mac address in capital letters without scripts. This address is found in the product sticker or directly in Qfinder Pro.
QNAP Firmware QSW-M2106PR-22S2T
QSS shows in its first section a Complete Dashboardwith the state of the port panel in real time (if you use network and POE link) and your side the general information. This section will remain present in all the following sections.
The lower section will be the one that changes, which in the first section provides Information about the power usedas well as network traffic. From the eyelashes you can manage the presentation of information.
The second section gives us the statistics for each portallowing to assign a denomination to each mouth, configure the speed limit and data flow. Later we will see that Link Aggregation is also admitted.
We look at the right side, where we have the “Configuration Guide” button where we are explained in detail what we can do in each section.
A third section is added to the POE management of the QNAP QSW-M2106PR-22S2Twhere we can see energy consumption, Configure each port individually With order of priority and Poe.
This is important when the complete capacity of the switch is used, since it will assign more energy to the most priority ports. It also allows Schedule use of the Poe.
VLAN It is a section that is available in all the QNAP Switches, to perform Port group In one or more switches and configure virtual networks, something totally basic in the business environment.
The next section is responsible for Generate link aggregationintegrating them into VLAN settings if we wish. Admits the Static modality and LACP For the dynamic management of the link between ports. It is also admitted LGA or link aggregation groups.
RSTP It is a protocol that allows Avoid network loopsensuring activity in backup ports in case of failures. We can activate this function in the ports individually.
LLDP (Link Layer Discovery Protocol) is another protocol focused on the business environment, in charge of collecting and distributing information to network devices, and detect possible defects.
We have system IGMP Snooping For the optimal use of the total switch bandwidth, being able to manage each port individually.
The ACL sections (Access control list) and QOs (Quality of service) are functions of the layer 3 which can also be managed in this switch individually in each port.
For the System's own functionsas time, IP, password, use of HTTPS in access, etc., we have the penultimate section, to end with the firmware update. In this case it seems that we have no SNMP service.
Speed test and Poe
To verify that the QNAP QSW-M2106PR-22S2T gives us its maximum capacity, we have connected Two teams with 10 Gbps LAN to obtain a measure in file transfer and data streams in parallel.
- Card 1: ASUS XG C100-C 10 GBPS
- Card 2: Asus Rog Areion 10 Gbps
Speed tests have been performed with Jperf 2.0.2 and those of data transfer with the explorer of Windows.
There are no surprises, the ports of 2.5 GBE and 10 GBE reach their maximum in stream transfer.
As for the use of Poewe only have a couple of Ajax surveillance cameras, enough to verify that information monitoring is very detailed, and that work perfectly.
Final words and conclusion about Qnap QSW-M2106PR-22S2T
QNAP presents one of its Switches poe more powerful and versatile For the business world, implantations of great capacity with Last generation wi-fi or even video surveillance, lighting or digital screens in shops.
And we have A total of 10 ports6 of them 2.5 GBE that will come phenomenal to connect Wi-Fi 6E access points, for example, and taking advantage of the bandwidth of 5 and 6 GHz.
The RJ45 ports of 10 gbe They will be useful for AP Wi-Fi 7, where 6 GHz can exceed 4 GBPs transfer, while The SFP+ They will be interesting to connect more switches or create in link to the server or router.
We recommend reading best nas on the market
All supplying a great capacity Poe ++ of 90W per port and up to 310W in total. Few devices consume so much, so we are left over, and this time Fans are not excessively noisy, But much more than a laptop or NAS.
QSS is a Operating system of great capacity and easy management for both administrators and normal users, since it has an assistant and detailed explanations in each section and everything can be done by clicking with graphic interface.
Among the most remarkable features, we have Link Aggregation, Advanced VLAN, QOs per port, HTTPS Access.
The price of this QNAP QSW-M2106PR-22S2T It is quite variable depending on the store that sells it, we find it From € 670 to € 800 as recommended figures. A great investment if we have especially demanding needs for a business or company.
|
ADVANTAGES |
Inconveniences |
| 6+ 2 ports with Poe ++ capacity 90W | |
| 6 RJ45 2.5 GBE + 2 RJ45 + 2 SFP + 10 GBE | |
| QSS System in layer 2 and layer 3 options | |
| Qos, Vlan, Lag, etc. | |
| Ideal for Wi-Fi 7 implementations and shops |
The Review Professional Team gives you the platinum medal:
Design – 85%
Performance – 95%
Ports – 95%
Firmware and Extras – 90%
Price – 89%
91%
QNAP QSW-M2106PR-22S2T is designed for an implantation of Wi-Fi 6e / 7 or a powerful budget surveillance system for 310W
